On this page
Most modern boilers restart on their own a few minutes after power returns. If yours stays off, check its fused switch is on, reset the clock on the programmer, turn the thermostat up and check the pressure gauge. If the boiler shows a fault or lockout light, press the reset button once and wait.
- Give the boiler a few minutes before you touch anything.
- A programmer that has lost its clock is the most common cause.
- Press reset once or twice only, never repeatedly.
- If you smell gas, call 0800 111 999 and do not reset.
Give it a few minutes first
A gas or oil boiler needs electricity for its controls, pump, fan and ignition, which is why a gas boiler stops in a power cut. When supply returns, most boilers run a short self-check and then fire up when the thermostat or timer next asks for heat. If the house is already close to its set temperature, the boiler may stay quiet for a while. That is normal.
Wait until the supply has been steady for five to ten minutes. Power sometimes flickers as it is restored, and there is no benefit in restarting the boiler several times.
Step-by-step checks if it does not restart
- Power to the boiler. Find the fused switch on the wall near the boiler and check it is on. Then look in your fuse box for a tripped switch and push it back up.
- The programmer or timer. Many lose the time in a cut, or revert to a factory schedule, so the boiler thinks it is the middle of the night. Reset the clock and check the heating and hot water are set to "on" or "auto".
- The thermostat. Turn the room thermostat up by a few degrees. A wireless or smart thermostat may need a few minutes, or fresh batteries, to reconnect to its receiver. Smart ones may also need your wifi router to be back online.
- The pressure gauge. On a sealed system the gauge normally reads somewhere between 1 and 2 bar when cold, and your manual gives the exact range. If it has dropped below 1, top up using the filling loop as the manual describes.
- The reset button. If the display shows a fault code or a red or flashing lockout light, press and hold the reset button for the time the manual states, often a few seconds. Then wait two or three minutes for the boiler to run its start-up sequence.
When to stop and call an engineer
If the boiler locks out again after one or two resets, leave it. A lockout is a safety feature, and resetting it over and over can mask a real fault. Note the fault code and call a Gas Safe registered engineer, or an OFTEC registered technician for an oil boiler.
If you smell gas, do not press reset or touch any electrical switches. Open doors and windows, turn the gas off at the meter if it is safe to do so, leave the property and call the gas emergency line on 0800 111 999. Never remove the boiler casing yourself.
While you wait for a repair, do not improvise heat with a barbecue, camping stove or patio heater indoors. They produce carbon monoxide, which has no smell. An audible alarm certified to EN 50291 near the boiler is a sensible fitting in any home, and our carbon monoxide alarm guide explains where to put one. For safe ways to stay comfortable in the meantime, see keeping warm without heating.
After a long cut in freezing weather
If the heating has been off for many hours in a hard frost, the condensate pipe may have frozen. This is the plastic waste pipe that runs from a condensing boiler to an outside drain. A blocked pipe causes a lockout, often with a gurgling noise. Thaw it by pouring warm (not boiling) water along the outside section, then reset. Our guide to keeping pipes from freezing covers the rest of the plumbing.
Once the boiler is running, radiators may need time to heat evenly. Then work through the rest of the house using our checklist for when the power comes back.
Common questions
Can a power cut damage a boiler?
Rarely. Occasionally a surge on return affects the control board or a fuse. If the display is completely dead with the power on, call an engineer.
Why is my boiler on but the radiators are cold?
The programmer has probably lost its settings, or the thermostat has not reconnected. Check both before assuming a fault.
Where is the reset button on a boiler?
It is usually on the front control panel, sometimes behind a drop-down flap, and is often marked with a flame symbol with a line through it or the word reset.
Reviewed against these sources on 18 November 2026. If official advice has changed since, follow the official advice.
General information only. This page is not professional, safety, medical, legal or financial advice, and it is not official guidance. No national blackout has been forecast or announced, and nothing here suggests one is expected. We are independent and have no connection to the government or any energy company. Always check the official sources linked on this page. Full disclaimer
Keep reading
Best power cut essentials: the blackout kit worth buying
The blackout kit worth buying for a UK power cut: a battery torch, a lantern, a power bank, a wind-up radio, an automatic light and a flask, with picks.
Read: Best power cut essentials: the blackout kitBest surge protectors for power cuts
Surge protectors for power cuts: extension leads that guard a TV, computer or router from the spike when the mains returns, chosen from Amazon UK listings.
Read: Best surge protectors for power cutsDriving during a wide power cut
Driving in a power cut: what to do when traffic lights are out, why fuel pumps and card machines stop, and how to use your car safely for power and news.
Read: Driving during a wide power cutThe first 24 hours without power
An hour-by-hour plan for the first 24 hours without electricity at home: what to do first, when food becomes a risk and how to ration phone battery.
Read: The first 24 hours without power